Product ID:LAMINAR X500 STBL GLOSS CLEAR PART A 7020
MSDS Date:02/24/1988
FSC:8030
NIIN:01-092-3879
Kit Part:Y
MSDS Number: BHRJD

MIDLAND DIVISION, THE DEXTER CORPORATION

31500 HAYMAN
HAYWARD, CA 94544
US

Emergency Phone: 415-796-4972

Info Phone: 415-471-7171

Preparer: K BUNTON

Cage: 91342

DEXTER CORP THE PACKAGING PRODUCTS DIV

WAUKEGAN, IL 60085-5614 US

Telephone: 847-623-4200

Cage: 91342

METHYL ETHYL KETONE (2-BUTANONE) (MEK) (SARA III)

CAS: 78-93-3

RTECS: EL6475000

Fraction By Weight: 10-20%

OSHA PEL 200 PPM/300 STEL

ACGIH TLV: 200 PPM/300STEL 9192

EPA Report Quantity: 5000 LBS

DOT Report Quantity: 5000 LBS

TOLUENE (SARA III)

CAS: 108-88-3

RTECS: XS5250000

Fraction By Weight: < 10%

OSHA PEL 200 PPM/150 STEL

ACGIH TLV: 50 PPM; 9293

EPA Report Quantity: 1000 LBS

DOT Report Quantity: 1000 LBS

2-ETHOXYETHYL ACETATE (CELLOSOLVE ACETATE) (EGEEA)

CAS: 111-15-9

RTECS: KK8225000

Fraction By Weight: 30-40%

OSHA PEL S,100 PPM

ACGIH TLV: S, 5 PPM; 9192

Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:OVEREXPOSURE BY INHALATION MAY CAUSE
IRRITATION OF THE RESPIRATORY TRACT, HEADACHE, DIZZINESS OR
DROWSINESS.
Effects of Overexposure:INHALATION: IRRITATION OF THE RESPIRATORY
TRACT, HEADACHE, DIZZINESS OR DROWSINESS. SKIN & EYE: IRRITANT TO
THE EYES AND SKIN, AND SKIN SENSITIVITY.
Medical Cond Aggravated by Exposure:RESPIRATORY PROBLEMS REPRODUCTIVE
SYSTEM.

First Aid:INHALATION: REMOVE FROM EXPOSURE. EYE: FLUSH IMMEDIATELY WITH
LARGE AMOUNTS OF RUNNING WATER AT LEAST 15 MINUTES. SKIN: REMOVE
CONTAMINATED CLOTHING & WASH SKIN WITH SOAP & WATER. INGESTION:
DRINK WAT ER. IF NECESSARY, CONSULT A PHYSICIAN FOR ANY OF THESE
CONDITIONS.

Flash Point Method:SCC
Flash Point:42.0 F/5.6 C
Lower Limits:1.20
Extinguishing Media:USE CARBON DIOXIDE, FOAM, DRY CHEMICAL, OR WATER
FOG.

Spill Release Procedures:REMOVE ALL SOURCES OF IGNITION, AVOID
BREATHING VAPORS, VENTILATE AREA AND REMOVE WITH INERT ABSORBANT
AND NON-SPARKING TOOLS. DISPOSE OF IN ACCORDANCE WITH LOCAL, STATE
AND FEDERAL REGULATIONS. BEFOR E ATTEMPTING TO CLEAN UP.

Handling and Storage Precautions:CONTAINERS SHOULD BE GROUNDED WHEN
POURING. AVOID FREE FALL OF LIQUID IN EXCESS OF A FEW INCHES.
ENSURE DRUM IS COMPLETELY EMPTY BEFORE WELDING, ETC.
Other Precautions:THE DRUM SHOULD BE INDUSTRIALLY CLEANED PRIOR TO
RE-USE. DO NOT FLAME CUT, BRAZE OR WELD WITHOUT A NIOSH APPOVED
RESPIRATOR OR APPROPRIATE VENTILATION.

Respiratory Protection:GENERAL DILUTION OR LOCAL EXHAUST FAILS TO
ADEQUATELY DILUTE THE TWA/PEL OF THE MATERIAL, THEN RESPIRATORY
PROTECTION SHOULD BE USED AS FOLLOWS: DO NOT BREATH VAPORS OR SPRAY
MIST. WEAR APPROPRIATE FI TTED RESPIRATOR APPROVED BY NIOSH/OSHA.
Ventilation:PROVIDE GEN DILUTION OR LOCAL EXHAUST VENT TO KEEP TWA &
LEL BELOW ACCEPTABLE LIMITS & TO REMOVE DECOMPOSITION PRODUCTS.
Protective Gloves:CHEM-RESISTANT GLOVES.
Eye Protection:CHEMICAL SPLASH GOGGLES/FACE SHIELD
Supplemental Safety and Health

Boiling Pt:B.P. Text:172F/78C
Vapor Density:> THAN AIR

Stability Indicator/Materials to Avoid:YES
Hazardous Decomposition Products:FUMES MAY CONTAIN CARBON MONOXIDE &
OXIDES OF NITROGEN. MAY PRODUCE HAZARDOUS FUMES WHEN HEATED TO
DECOMP AS IN WELDING

Waste Disposal Methods:DISPOSE OF IN ACCORDANCE WITH LOCAL, STATE AND
FEDERAL REGULATIONS. BEFORE ATTEMPTING TO CLEAN UP.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.